484 lines
22 KiB
Plaintext
484 lines
22 KiB
Plaintext
|
Reliance LG LSP 340 Series WLL Modem Setup HOWTO
|
|||
|
|
|||
|
Dhiraj Gaur
|
|||
|
|
|||
|
dhiraj<EFBFBD>dot<EFBFBD>gaur<EFBFBD>_at_<EFBFBD>gmail<EFBFBD>dot<EFBFBD>com
|
|||
|
|
|||
|
dhiraj<EFBFBD>_at_<EFBFBD>mail<EFBFBD>dot<EFBFBD>nplindia<EFBFBD>dot<EFBFBD>ernet<EFBFBD>dot<EFBFBD>in<EFBFBD>
|
|||
|
Revision History
|
|||
|
Revision 1.0 2005-06-21
|
|||
|
Revised by Machtelt Garrels for inclusion in TLDP.
|
|||
|
|
|||
|
|
|||
|
This document explains how to set up and configure Reliance or TATA Indicomm
|
|||
|
WLL phones on Linux, using a serial cable instead of the (default) USB cable.
|
|||
|
It also has instructions on how to build the cable yourself.
|
|||
|
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
Table of Contents
|
|||
|
1. Introduction
|
|||
|
2. System Requirements
|
|||
|
3. Activating Internet Services on your Handset
|
|||
|
4. Checking for PPP Support
|
|||
|
5. Configuring your Phone
|
|||
|
6. PPP Configuration
|
|||
|
7. Let's Get Started
|
|||
|
8. References
|
|||
|
9. Feedback
|
|||
|
10. Licensing information and liability
|
|||
|
|
|||
|
1. Introduction
|
|||
|
|
|||
|
This HOWTO is for people who have Reliance or TATA Indicomm WLL phones and
|
|||
|
wish to access Internet on their desktops/laptops running GNU/Linux using
|
|||
|
serial cable (NOT a USB CABLE).
|
|||
|
|
|||
|
No software provided by Reliance was used, but I did search the Internet for
|
|||
|
the modem query strings which are required during PPP setup.
|
|||
|
|
|||
|
I have tried this setup on Slackware Linux 10.1 with a 2.4.29 kernel and I am
|
|||
|
pretty confident that this trick will work on other Linux distributions as
|
|||
|
well.
|
|||
|
|
|||
|
The HOWTO assumes that you have a fair knowledge about your Linux
|
|||
|
distribution (BSD or System V style) and that PPP support is pre-compiled in
|
|||
|
your Linux kernel.
|
|||
|
|
|||
|
In this HOWTO we are talking about the serial cable for the following
|
|||
|
reasons:
|
|||
|
|
|||
|
1. The cable provided by Reliance or TATA is very expensive (about 1400
|
|||
|
rupees) and the software provided supports only MS Windows.The cable
|
|||
|
typically has a USB interface on one end and an RJ-45 interface on the
|
|||
|
other. However, for these phones phones a cheaper cable is available on
|
|||
|
the market (only 100 rupees). This cable has a serial interface on one
|
|||
|
end and an RJ-45 on the other. You can make this cable yourself. The
|
|||
|
procedure is discussed later in this HOWTO. Why waste money when you can
|
|||
|
assemble your own cable or purchase the cheaper one?
|
|||
|
|
|||
|
2. USB cables have some glitches for the WLL handsets, especially the LG
|
|||
|
ones. I have no idea about other handsets, your input is welcome if you
|
|||
|
know about other sets. The advantage in using a USB cable is that you can
|
|||
|
connect at 153.6 kbps as the handsets have an inbuilt modem which is
|
|||
|
capable for speeds upto 170kbps.
|
|||
|
|
|||
|
3. On the numerous forums I searched on the net I found that all talked only
|
|||
|
about the USB cable and not about the serial one. I thought it was high
|
|||
|
time to write this HOWTO to help fellow Linux users.
|
|||
|
|
|||
|
|
|||
|
Note But I have a USB cable!
|
|||
|
<EFBFBD> If you have the USB cable after all, visit [http://www.hackgnu.org/
|
|||
|
ril-howto.html] http://www.hackgnu.org/ril-howto.html for information
|
|||
|
about setting up Internet access using LG/SAMSUNG CDMA sets.
|
|||
|
|
|||
|
This link is also helpful: [http://www.linuxsolved.com/forums/
|
|||
|
ftopic1178.html] http://www.linuxsolved.com/forums/ftopic1178.html
|
|||
|
|
|||
|
Unfortunately the LG/SAMSUNG CDMA mobile uses USB cables only, but the
|
|||
|
good news is that these USB cables are also available on the market.
|
|||
|
Purchase them at your local computer vendor's. As per my last
|
|||
|
information such cables cost only 200 rupees.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
2. System Requirements
|
|||
|
|
|||
|
You will need a GNU/Linux system with a kernel having PPP support
|
|||
|
pre-compiled. I have tested that both the 2.4.29 kernel and the 2.6.x series
|
|||
|
kernel work fine. Performance seems to be better using a 2.6.x kernel. If you
|
|||
|
see that some kernel modules are missing then configure and recompile the
|
|||
|
kernel with PPP support.
|
|||
|
|
|||
|
Check with Section 4 for the configuration of PPP.
|
|||
|
|
|||
|
A connecting serial cable which has on one end an RJ-45 connector which plugs
|
|||
|
into the phone and on the other end has an RS-232 serial connector which is
|
|||
|
plugged into the serial port of the PC.
|
|||
|
|
|||
|
I built my cable myself. I used a CAT 5 cable which has four pairs of UTP
|
|||
|
copper. CAT 5 cable is the same cable which is used for networking your
|
|||
|
system to a LAN. While you can use any type of cable, CAT 5 will assure a
|
|||
|
good quality of the signal that is sent over the wire. A typical
|
|||
|
configuration looks like this:
|
|||
|
|
|||
|
RS-232C Serial Female connector, which is plugged into the PC:
|
|||
|
___________________
|
|||
|
\ /
|
|||
|
\ 5 4 3 2 1 /
|
|||
|
\ 9 8 7 6 /
|
|||
|
\___________/
|
|||
|
|
|||
|
|
|||
|
|
|||
|
Now let's start with the PIN Configuration
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 1 - White Brown cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 2 - Blue cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 3 - White Green cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 4 - Green cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 5 - White Blue cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 6 - Brown cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 7 - White Orange cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 8 - Orange cable
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>PIN 9 - Leave empty (we are only using 8 pins)
|
|||
|
|
|||
|
|
|||
|
Note Serial connection details
|
|||
|
<EFBFBD> Three strings would be enough for a serial connection, but it turned out
|
|||
|
that the signal is better when you use 5. The other strings are used for
|
|||
|
extra rigidness and support of the cable.
|
|||
|
|
|||
|
Now on to the RJ-45 connector, which is plugged into the WLL Phone RJ-45
|
|||
|
jack:
|
|||
|
[8 7 6 5 4 3 2 1]
|
|||
|
----
|
|||
|
-
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>1 - White Orange
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>2 - Orange
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>3 - White Green
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>4 - Blue
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>5 - White Blue
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>6 - Green
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>7 - White Brown
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>8 - Brown
|
|||
|
|
|||
|
|
|||
|
Tip How to hold the connector
|
|||
|
<EFBFBD> If you are confused as to which way to hold the connector, make sure that
|
|||
|
you are holding the connector in such a way that its notch pin is facing
|
|||
|
towards the floor and that the open portion (portion from where the wires
|
|||
|
enter) is facing away from you.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
3. Activating Internet Services on your Handset
|
|||
|
|
|||
|
To get Internet services activated on your handset you may contact the
|
|||
|
customer care center of your service provider. In the case of the Reliance
|
|||
|
the service is pre-activated.
|
|||
|
|
|||
|
For establishing the connection on a Reliance, the user name is the phone
|
|||
|
number without the prefix 0 in the STD code. For instance, if your STD code
|
|||
|
is 0124 and telephone number is 3456789 then your user name is 1243456789.
|
|||
|
Your password is the same as your user name. When using the TATA Indicomm
|
|||
|
user name and password are "internet" (without quotes).
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
4. Checking for PPP Support
|
|||
|
|
|||
|
Although PPP support is provided in almost all Linux distributions but it is
|
|||
|
still better to check whether it is present on your system. You can use
|
|||
|
checkconfig or, better still, look into the /usr/sbin directory and locate
|
|||
|
PPP binaries with the command
|
|||
|
|
|||
|
ls -al ppp*
|
|||
|
|
|||
|
If you get a listing like this:
|
|||
|
-rwxr-xr-x 1 root root 3438 2005-05-28 14:56 ppp-go*
|
|||
|
-rwxr-xr-x 1 root bin 1787 2004-02-26 21:36 ppp-off*
|
|||
|
lrwxrwxrwx 1 root root 6 2005-05-28 14:17 ppp-on -> ppp-go*
|
|||
|
lrwxrwxrwx 1 root root 7 2005-05-28 14:17 ppp-stop -> ppp-off*
|
|||
|
-rwxr-xr-x 1 root bin 346812 2004-02-26 21:36 pppd*
|
|||
|
-rwxr-xr-x 1 root bin 37916 2004-02-26 21:36 pppdump*
|
|||
|
-rwxr-xr-x 1 root bin 25936 2003-03-02 22:05 pppoe*
|
|||
|
-rwxr-xr-x 1 root bin 22308 2003-03-02 22:05 pppoe-relay*
|
|||
|
-rwxr-xr-x 1 root bin 35084 2003-03-02 22:05 pppoe-server*
|
|||
|
-rwxr-xr-x 1 root bin 12028 2003-03-02 22:05 pppoe-sniff*
|
|||
|
-rwxr-xr-x 1 root bin 58527 2004-02-26 21:36 pppsetup*
|
|||
|
-rwxr-xr-x 1 root bin 9192 2004-02-26 21:36 pppstats*
|
|||
|
|
|||
|
then PPP support is definitely present.
|
|||
|
|
|||
|
Similarly, look into /etc/ppp directory, which contains the PPP options file
|
|||
|
and some other files configuring PPP:
|
|||
|
-rw------- 1 root root 78 2004-02-26 21:36 chap-secrets
|
|||
|
-rw------- 1 root root 1625 2005-05-28 14:35 connect-errors
|
|||
|
-rw-r--r-- 1 root root 938 2003-03-02 22:04 firewall-masq
|
|||
|
-rw-r--r-- 1 root root 836 2003-03-02 22:04 firewall-standalone
|
|||
|
-rwxr-xr-x 1 root root 1208 2005-05-28 14:56 ip-down*
|
|||
|
-rwxr-xr-x 1 root root 1208 2005-05-28 14:29 ip-down.OLD*
|
|||
|
-rwxr-xr-x 1 root root 1945 2005-05-28 14:56 ip-up*
|
|||
|
-rwxr-xr-x 1 root root 1945 2005-05-28 14:29 ip-up.OLD*
|
|||
|
-rw------- 1 root root 541 2005-05-28 14:58 options
|
|||
|
-rw------- 1 root root 656 2005-05-28 14:56 options.demand
|
|||
|
-rw-r--r-- 1 root root 9975 2005-05-28 11:21 options.old
|
|||
|
-rw------- 1 root root 216 2005-05-28 14:56 pap-secrets
|
|||
|
drwxr-xr-x 2 root root 4096 2003-03-02 22:05 plugins/
|
|||
|
-rw-r--r-- 1 root root 104 2003-03-02 22:04 pppoe-server-options
|
|||
|
-rw-r--r-- 1 root root 4562 2003-03-02 22:04 pppoe.conf
|
|||
|
-rw------- 1 root root 129 2005-05-28 15:12 pppscript
|
|||
|
-rw------- 1 root root 8941 2005-05-28 14:56 pppsetup.txt
|
|||
|
|
|||
|
For the sake of safety do copy your original options file to a file
|
|||
|
options.old so that you can revert back to your original setup should you
|
|||
|
have troubles.
|
|||
|
|
|||
|
See [http://www.tldp.org/HOWTO/PPP-HOWTO/kernel-configuration.html] the PPP
|
|||
|
HOWTO Chapter 10 for more information on PPP support in the Linux kernel.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
5. Configuring your Phone
|
|||
|
|
|||
|
Currently Reliance comes with one of two brands of handsets: LG and Samsung.
|
|||
|
TATA Indicom also provides two handsets: LG and AXESSTEL.
|
|||
|
|
|||
|
Plug the cable to the phone and also to the system.
|
|||
|
|
|||
|
It is important to note that all these phones act as a serial modem so they
|
|||
|
do not require a driver or anything. After you have connected your phone to
|
|||
|
the cable, the cable is plugged in either COM1 or COM2 (and not COM3 or COM4,
|
|||
|
as these are virtual ports).
|
|||
|
|
|||
|
Remember:
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>COM1 in LINUX is /dev/ttyS0
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>COM2 is LINUX is /dev/ttyS1
|
|||
|
|
|||
|
|
|||
|
Your phone modem works on either of the two ports, but I suggest that first
|
|||
|
try /dev/ttyS1, so as not to disturb other peripherics on your system that
|
|||
|
are also using a serial port, which would then usually be on /dev/ttyS0.
|
|||
|
|
|||
|
First check if your COM port is fine using the command
|
|||
|
|
|||
|
setserial /dev/ttyS1 -a
|
|||
|
|
|||
|
If it displays something like this:
|
|||
|
dev/ttyS1, Line 1, UART: 16550A, Port: 0x02f8, IRQ: 3
|
|||
|
Baud_base: 115200, close_delay: 50, divisor: 0
|
|||
|
closing_wait: 3000
|
|||
|
Flags: spd_normal skip_test
|
|||
|
|
|||
|
|
|||
|
then your COM port is fine. If this does not work, it is possible that PPP
|
|||
|
support is not configured after all. Return to Section 4 to check. If you are
|
|||
|
sure that PPP support is configured on your system, maybe the problem is with
|
|||
|
the COM port. You could try the other port in that case.
|
|||
|
|
|||
|
Now go to the shell and type
|
|||
|
|
|||
|
cat /dev/ttyS1
|
|||
|
|
|||
|
If this prints nothing, your phone is configured. Type CTRL+C to exit.
|
|||
|
|
|||
|
If your modem is not configured, the cat command would give an error message
|
|||
|
like this:
|
|||
|
cat: /dev/ttyS1: No such device
|
|||
|
|
|||
|
Alternately, in case you use KDE, start the KPPP program: go to the desktop
|
|||
|
and press Alt+F2 and type "kppp" in the box which appears. This will start
|
|||
|
KPPP.
|
|||
|
|
|||
|
Testing using KPPP:
|
|||
|
|
|||
|
Click on the Configure button. Go to the Modem tab.
|
|||
|
There add a new modem on /dev/ttyS1and click OK. Now select the newly created
|
|||
|
modem and click the EDITbutton. In the new box which appears, select Modemand
|
|||
|
then click Query modem. If the modem is properly set then you will get the
|
|||
|
proper status of the modem. It will first say something like "Finding Modem",
|
|||
|
then some more messages.
|
|||
|
|
|||
|
Warning Lock file
|
|||
|
<EFBFBD> BE SURE TO UNCHECK THE USE LOCK FILE CHECKBOX in the modem
|
|||
|
properties, else it may give some random errors.
|
|||
|
|
|||
|
If all is fine you will be presented with a window with some blank textboxes
|
|||
|
and you can go ahead.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
6. PPP Configuration
|
|||
|
|
|||
|
Make an easy link to your modem device:
|
|||
|
|
|||
|
ln -s /dev/ttyS1 /dev/modem
|
|||
|
|
|||
|
Now change to the /usr/sbin directory and look for ppp files. Look for either
|
|||
|
a pppsetup or a pppconfig script. You may directly start this script to set
|
|||
|
up PPP on your system. On my Slackware system I typed pppsetup and started
|
|||
|
the script. This script asks for various parameters for connecting via the
|
|||
|
ISP.
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>It first asks for the phone number to dial -- enter "atdt#777", where 777
|
|||
|
is replaced by the number that you need to dial.
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>It then asks for the modem -- select /dev/ttyS1
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>Baud Rate -- select "115200"
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>Callback -- Answer "NO"
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>Modem INIT String -- "ATZ OK "at+crm=1" OK"
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>ISP Domain Name -- Leave blank
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>DNS Server Address -- Enter a valid DNS Server IP, for instance
|
|||
|
"202.41.97.3" or "202.41.97.132", or leave blank
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>Authentication -- "PAP"
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>Username
|
|||
|
|
|||
|
<EFBFBD><EFBFBD>*<2A>Password
|
|||
|
|
|||
|
|
|||
|
Refer to Section 3 for Username and Password.
|
|||
|
|
|||
|
Finally it shows you your configuration.
|
|||
|
|
|||
|
Some more work needs to be done. We need to edit the options file present in
|
|||
|
the /etc/ppp folder. We need to check if the following entries are present in
|
|||
|
the file:
|
|||
|
lock
|
|||
|
defaultroute
|
|||
|
noipdefault
|
|||
|
modem
|
|||
|
/dev/ttyS1
|
|||
|
115200
|
|||
|
crtscts
|
|||
|
noauth
|
|||
|
passive
|
|||
|
asyncmap 0
|
|||
|
|
|||
|
Note The noauth option
|
|||
|
<EFBFBD> Remember that noauth is by default commented; you need to uncomment it.
|
|||
|
|
|||
|
You can use egrep -v '#|^ *$' /etc/ppp/options to list only the options
|
|||
|
present in this file so as to quickly judge which ones are missing or
|
|||
|
incorrect.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
7. Let's Get Started
|
|||
|
|
|||
|
For testing purposes log in as root and open two different shells.
|
|||
|
|
|||
|
In one shell issue the command
|
|||
|
|
|||
|
tail -f /var/log/messages
|
|||
|
|
|||
|
Start the PPP connection in the other shell using the command
|
|||
|
|
|||
|
ppp-on
|
|||
|
|
|||
|
In the first shell you will see various messages indicating that the modem is
|
|||
|
initialized and that the connection is being established. My /var/log/
|
|||
|
messages looks like this:
|
|||
|
May 29 06:14:06 dhiraj pppd[2341]: pppd 2.4.2 started by root, uid 0
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: timeout set to 60 seconds
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: abort on (ERROR)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: abort on (BUSY)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: abort on (NO CARRIER)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: abort on (NO DIALTONE)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: send (ATZ^M)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: expect (OK)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: ATZ^M^M
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: OK
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: -- got it
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: send (at+crm=1^M)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: expect (OK)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: ^M
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: at+crm=1^M^M
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: OK
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: -- got it
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: send (atdt#777^M)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: timeout set to 75 seconds
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: expect (CONNECT)
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: ^M
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: atdt#777^M^M
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: CONNECT
|
|||
|
May 29 06:14:07 dhiraj chat[2343]: -- got it
|
|||
|
May 29 06:14:07 dhiraj pppd[2341]: Serial connection established.
|
|||
|
May 29 06:14:07 dhiraj pppd[2341]: Using interface ppp0
|
|||
|
May 29 06:14:07 dhiraj pppd[2341]: Connect: ppp0 <--> /dev/ttyS1
|
|||
|
May 29 06:14:13 dhiraj pppd[2341]: PAP authentication succeeded
|
|||
|
May 29 06:14:13 dhiraj kernel: PPP BSD Compression module registered
|
|||
|
May 29 06:14:13 dhiraj kernel: PPP Deflate Compression module registered
|
|||
|
May 29 06:14:14 dhiraj pppd[2341]: local IP address 220.224.45.140
|
|||
|
May 29 06:14:14 dhiraj pppd[2341]: remote IP address 97.235.2.5
|
|||
|
|
|||
|
Now open your browser and get started.
|
|||
|
|
|||
|
In case the browser gives the error that the server name is not being
|
|||
|
resolved, open the file /etc/resolve.conf and add the entry
|
|||
|
namesserver 202.41.97.9
|
|||
|
nameserver 202.41.97.132
|
|||
|
|
|||
|
|
|||
|
These are two valid DNS servers of Ernet India Labs, located in New Delhi.
|
|||
|
Your Internet Service Provider probably provides its own name service, use
|
|||
|
the IP addresses of the servers they recommend.
|
|||
|
|
|||
|
When you are finished surfing the net you may stop the connection using
|
|||
|
|
|||
|
ppp-off
|
|||
|
|
|||
|
in the second shell. In the other shell window you will get something like
|
|||
|
this :
|
|||
|
May 29 06:16:15 dhiraj pppd[2341]: Terminating on signal 2.
|
|||
|
May 29 06:16:15 dhiraj pppd[2341]: Connection terminated.
|
|||
|
May 29 06:16:15 dhiraj pppd[2341]: Connect time 2.2 minutes.
|
|||
|
May 29 06:16:15 dhiraj pppd[2341]: Sent 3401 bytes, received 1563 bytes.
|
|||
|
May 29 06:16:16 dhiraj pppd[2341]: Connect time 2.2 minutes.
|
|||
|
May 29 06:16:16 dhiraj pppd[2341]: Sent 3401 bytes, received 1563 bytes.
|
|||
|
May 29 06:16:16 dhiraj pppd[2341]: Exit.
|
|||
|
|
|||
|
|
|||
|
Stop the messages output using Ctrl+C.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
8. References
|
|||
|
|
|||
|
For info about accessing Internet using LG/SAMSUNG CDMA sets via USB cable go
|
|||
|
to [http://www.hackgnu.org/ril-howto.html] http://www.hackgnu.org/
|
|||
|
ril-howto.html.
|
|||
|
|
|||
|
This link is also helpful: [http://www.linuxsolved.com/forums/
|
|||
|
ftopic1178.html] http://www.linuxsolved.com/forums/ftopic1178.html.
|
|||
|
|
|||
|
All the information in this HOWTO comes partly from these two links, the
|
|||
|
[http://tldp.org/HOWTO/PPP-HOWTO/index.html] PPP-HOWTO and partly from my
|
|||
|
research and development in the Linux world.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
9. Feedback
|
|||
|
|
|||
|
Mail your suggestions, requests and queries to the author.
|
|||
|
-----------------------------------------------------------------------------
|
|||
|
|
|||
|
10. Licensing information and liability
|
|||
|
|
|||
|
This document is copyrighted 2005 by Dhiraj Gaur. Permission is granted to
|
|||
|
copy, distribute and/or modify this document under the terms of the GNU Free
|
|||
|
Documentation License, Version 1.1 or any later version published by the Free
|
|||
|
Software Foundation; with no Invariant Sections, with no Front-Cover Texts,
|
|||
|
and with no Back-Cover Texts. A copy of the license is available at [http://
|
|||
|
www.gnu.org/copyleft/fdl.html] http://www.gnu.org/copyleft/fdl.html.
|
|||
|
|
|||
|
Linux is a registered trademark of Linus Torvalds.
|
|||
|
|
|||
|
No liability for the contents of this document can be accepted. Use the
|
|||
|
concepts, examples and information at your own risk. There may be errors and
|
|||
|
inaccuracies, that could be damaging to your system. Proceed with caution,
|
|||
|
and although this is highly unlikely, the author(s) do not take any
|
|||
|
responsibility.
|
|||
|
|
|||
|
All copyrights are held by their by their respective owners, unless
|
|||
|
specifically noted otherwise. Use of a term in this document should not be
|
|||
|
regarded as affecting the validity of any trademark or service mark. Naming
|
|||
|
of particular products or brands should not be seen as endorsements.
|