man-pages/man4/lirc.4

.\" Copyright (c) 2015-2016, Alec Leamas
.\"
.\" %%%LICENSE_START(GPLv2+_DOC_FULL)
.\" This is free documentation; you can redistribute it and/or
.\" modify it under the terms of the GNU General Public License as
.\" published by the Free Software Foundation; either version 2 of
.\" the License, or (at your option) any later version.
.\"
.\" The GNU General Public License's references to "object code"
.\" and "executables" are to be interpreted as the output of any
.\" document formatting or typesetting system, including
.\" intermediate and printed output.
.\"
.\" This manual is distributed in the hope that it will be useful,
.\" but WITHOUT ANY WARRANTY; without even the implied warranty of
.\" MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
.\" GNU General Public License for more details.
.\"
.\" You should have received a copy of the GNU General Public
.\" License along with this manual; if not, see
.\" <http://www.gnu.org/licenses/>.
.\" %%%LICENSE_END
.TH LIRC 4 2016-07-17 "Linux" "Linux Programmer's Manual"
.SH NAME
lirc \- lirc devices
.SH DESCRIPTION
.PP
The
.B /dev/lirc*
character devices provide a low-level
bi-directional interface to infra-red (IR) remotes.
When receiving data, the driver works in two different modes depending
on the underlying hardware.
.PP
Some hardware (typically TV-cards) decodes the IR signal internally
and just provides decoded button presses as integer values.
Drivers for this kind of hardware work in
.BR LIRC_MODE_LIRCCODE
mode.
Such hardware usually does not support sending IR signals.
Furthermore, it usually only works with a specific remote which is
bundled with, for example, a TV-card.
.PP
Other hardware provides a stream of pulse/space durations.
Such drivers work in
.BR LIRC_MODE_MODE2
mode.
Sometimes, this kind of hardware also supports
sending IR data.
Such hardware can be used with (almost) any kind of remote.
.PP
The \fBLIRC_GET_REC_MODE\fR ioctl (see below) allows probing for the
mode.
.\"
.SS Reading input with the LIRC_MODE_MODE2 drivers
.PP
In the \fBLIRC_MODE_MODE2 mode\fR, the data returned by
.BR read (2)
provides 32-bit values representing a space or a pulse duration, by
convention typed as
.IR lirc_t .
The time of the duration (microseconds) is encoded in the lower 24 bits.
The upper 8 bit reflects the type of package:
.TP 4
.BR LIRC_MODE2_SPACE .
Value reflects a space duration (microseconds).
.TP 4
.BR LIRC_MODE2_PULSE .
Value reflects a pulse duration (microseconds).
.TP 4
.BR LIRC_MODE2_FREQUENCY .
Value reflects a frequency (Hz); see the
.B LIRC_SET_MEASURE_CARRIER_MODE
ioctl.
.TP 4
.BR LIRC_MODE2_TIMEOUT .
The package reflects a timeout; see the
.B LIRC_SET_REC_TIMEOUT_REPORTS
ioctl.
.\"
.SS Reading input with the
.B LIRC_MODE_LIRCCODE
drivers
.PP
In the \fBLIRC_MODE_LIRCCODE\fR
mode, the data returned by
.BR read (2)
reflects decoded button presses.
The length of each packet can be retrieved using
the \fBLIRC_GET_LENGTH\fR ioctl.
Reads must be done in blocks matching
the bit count returned by the \fBLIRC_GET_LENGTH\fR ioctl, rounded
up so it matches full bytes.
.\"
.SS Sending data
.PP
When sending data, only the \fBLIRC_MODE_PULSE\fR
mode is supported.
The data written to the character device using
.BR write (2)
is a pulse/space sequence of integer values.
Pulses and spaces are only marked implicitly by their position.
The data must start and end with a pulse, thus it must always include
an odd number of samples.
The
.BR write (2)
function blocks until the data has been transmitted by the
hardware.
If more data is provided than the hardware can send, the
.BR write (2)
call fails with the error
.BR EINVAL
.\"
.SH IOCTL COMMANDS
.PP
The complete list of ioctl commands is maintained in the kernel
documentation, see SEE ALSO.
The ioctl commands presented here is a subset of the kernel
documentation.
.PP
The LIRC device's ioctl definition is bound by the ioctl function
definition of struct file_operations, leaving us with an unsigned
int for the ioctl command and an unsigned long for the argument.
For the purposes of ioctl portability across 32-bit and 64-bit architectures,
these values are capped to their 32-bit sizes.
.PP
.nf
#include <lirc/include/media/lirc.h>    /* But see BUGS */
int ioctl(int fd, int cmd, ...);
.fi
.PP
The following ioctls can be used to probe or change specific lirc
hardware settings.
Many require a third argument, usually an
.IR int .
referred to below as
.IR val .
.PP
In general, each driver should have a default set of settings.
The driver implementation is expected to re-apply the default settings
when the device is closed by user space, so that every application
opening the device can rely on working with the default settings
initially.
.\"
.SS Always Supported Commands
.PP
\fI/dev/lirc*\fR devices always support the following commands:
.TP 4
.BR LIRC_GET_FEATURES " (\fIvoid\fP)"
Returns a bit mask of combined features bits; see FEATURES.
Some drivers have dynamic features which are not updated until after an
.I init()
command.
If a driver does not announce support of certain features, calling of
the corresponding ioctls is undefined.
.TP
.BR LIRC_GET_REC_MODE
Return the receive mode, which will be one of:
.RS 4
.TP
.BR LIRC_MODE_MODE2 " (\fIvoid\fP)"
The driver returns a sequence of pulse/space durations.
.TP
.BR LIRC_MODE_LIRCCODE
The driver returns integer values, each of which represents a decoded
button press.
.RE
.PP
If a device returns an error code for
.BR LIRC_GET_REC_MODE ,
it is safe to assume it is not a lirc device.
.\"
.SS Optional Commands
.PP
Some lirc devices support commands listed below.
Unless otherwise stated, these fail with the error \fBENOIOCTLCMD\fR
or with the error \fBENOSYS\fR if the operation
isn't supported, or with the error \fBEINVAL\fR if the operation
failed.
.TP
.BR LIRC_SET_REC_MODE " (\fIint\fP)"
Set the receive mode.
.IR val
is either
.BR LIRC_MODE_LIRCCODE
or
.BR LIRC_MODE_MODE2 .
.TP
.BR LIRC_GET_LENGTH " (\fIvoid\fP)"
Return the length of the returned codes for
.BR LIRC_MODE_LIRCCODE -type
drivers, otherwise fail with the error
.BR ENOIOCTLCMD .
.TP
.BR LIRC_GET_SEND_MODE " (\fIvoid\fP)"
Return the send mode.
Currently, only
.BR LIRC_MODE_PULSE
is supported.
.TP
.BR LIRC_SET_SEND_MODE " (\fIint\fP)"
Set the send mode.
Currently serves no purpose since only
.BR LIRC_MODE_PULSE
is supported.
.TP
.BR LIRC_GET_SEND_CARRIER " (\fIvoid\fP)"
Get the modulation frequency (Hz).
.TP
.BR LIRC_SET_SEND_CARRIER " (\fIint\fP)"
Set the modulation frequency.
The argument is the frequency (Hz).
.TP
.BR LIRC_GET_SEND_CARRIER " (\fIvoid\fP)"
Get the modulation frequency used when decoding (Hz).
.TP
.BR SET_SEND_DUTY_CYCLE " (\fIint\fP)"
Set the carrier duty cycle.
.I val
is a number in the range [0,100] which
describes the pulse width as a percentage of the total cycle.
Currently, no special meaning is defined for 0 or 100, but the values
are reserved for future use.
.IP
.TP
.BR LIRC_GET_MIN_TIMEOUT " (\fIvoid\fP)", " "\
LIRC_GET_MAX_TIMEOUT " (\fIvoid\fP)"
Some devices have internal timers that can be used to detect when
there's no IR activity for a long time.
This can help
.BR lircd (8)
in detecting that an IR signal is finished and can speed up the
decoding process.
These operations
return integer values with the minimum/maximum timeout that can be
set (microseconds).
Some devices have a fixed timeout.
For such drivers,
.BR LIRC_GET_MIN_TIMEOUT
and
.BR LIRC_GET_MAX_TIMEOUT
will return the same value.
.TP
.BR LIRC_SET_REC_TIMEOUT " (\fIint\fP)"
Set the integer value for IR inactivity timeout (microseconds).
To be accepted, the value must be within the limits defined by
.BR LIRC_GET_MIN_TIMEOUT
and
.BR LIRC_GET_MAX_TIMEOUT .
A value of 0 (if supported by the hardware) disables all hardware
timeouts and data should be reported as soon as possible.
If the exact value cannot be set, then the next possible value
.I greater
than the given value should be set.
.TP
.BR LIRC_SET_REC_TIMEOUT_REPORTS " (\fIint\fP)"
Enable
.RI ( val
is 1) or disable
.RI ( val
is 0) timeout packages in
.BR LIRC_MODE_MODE2 .
By default, timeout reports should be turned off.
.TP
.BR LIRC_SET_REC_CARRIER " (\fIint\fP)"
Set the receive carrier frequency (Hz).
.TP
.BR LIRC_SET_REC_CARRIER_RANGE " (\fIint\fP)"
After opening device, the first use of this operation
sets the lower bound of the carrier range,
and the second use sets the upper bound (Hz).
.TP
.BR LIRC_SET_MEASURE_CARRIER_MODE " (\fIint\fP)"
Enable
.RI ( val
is 1) or disable
.RI ( val
is 0) the measure mode.
If enabled, from the next key press on, the driver will send
.BR LIRC_MODE2_FREQUENCY
packets.
By default this should be turned off.
.TP
.BR LIRC_GET_REC_RESOLUTION " (\fIvoid\fP)"
Return the driver resolution (microseconds).
.TP
.BR LIRC_GET_MIN_FILTER_PULSE " (\fIvoid\fP)", " " \
LIRC_GET_MAX_FILTER_PULSE " (\fIvoid\fP)"
Some devices are able to filter out spikes in the incoming signal
using given filter rules.
These ioctls return the hardware capabilities that describe the bounds
of the possible filters.
Filter settings depend on the IR protocols that are expected.
.BR lircd (8)
derives the settings from all protocols definitions found in its
.BR lircd.conf (5)
config file.
.TP
.BR LIRC_GET_MIN_FILTER_SPACE " (\fIvoid\fP)", " " \
LIRC_GET_MAX_FILTER_SPACE " (\fIvoid\fP)"
See
.BR LIRC_GET_MIN_FILTER_PULSE .
.TP
.BR LIRC_SET_REC_FILTER " (\fIint\fP)"
Pulses/spaces shorter than this (microseconds) are filtered out by
hardware.
.TP
.BR LIRC_SET_REC_FILTER_PULSE " (\fIint\fP)", " " \
LIRC_SET_REC_FILTER_SPACE " (\fIint\fP)"
Pulses/spaces shorter than this (microseconds) are filtered out by
hardware.
If filters cannot be set independently for pulse/space, the
corresponding ioctls must return an error and
.BR LIRC_SET_REC_FILTER
should be used instead.
.TP
.BR LIRC_SET_TRANSMITTER_MASK
Enable the set of transmitters specified in
.IR val ,
which contains a bit mask where each enabled transmitter is a 1.
The first transmitter is encoded by the least significant bit, and so on.
When an invalid bit mask is given, for example a bit is set even
though the device does not have so many transmitters,
this operation returns the
number of available transmitters and does nothing otherwise.
.TP
.BR LIRC_SET_WIDEBAND_RECEIVER " (\fIint\fP)"
Some devices are equipped with a special wide band receiver which is
intended to be used to learn the output of an existing remote.
This ioctl can be used to enable
.RI ( val
equals 1) or disable
.RI ( val
equals 0) this functionality.
This might be useful for devices that otherwise have narrow band
receivers that prevent them to be used with certain remotes.
Wide band receivers may also be more precise.
On the other hand its disadvantage usually is reduced range of
reception.
.IP
Note: wide band receiver may be implicitly enabled if you enable
carrier reports.
In that case, it will be disabled as soon as you disable carrier reports.
Trying to disable a wide band receiver while carrier reports are active
will do nothing.
.TP
.BR LIRC_SETUP_START " (\fIvoid\fP), " LIRC_SETUP_END " (\fIvoid\fP)"
Setting of several driver parameters can be optimized by bracketing
the actual ioctl calls
.BR LIRC_SETUP_START
and
.BR LIRC_SETUP_END .
When a driver receives a
.BR LIRC_SETUP_START
ioctl, it can choose to not commit further setting changes to the
hardware until a
.BR LIRC_SETUP_END
is received.
But this is open to the driver implementation and every driver
must also handle parameter changes which are not encapsulated by
.BR LIRC_SETUP_START
and
.BR LIRC_SETUP_END .
Drivers can also choose to ignore these ioctls.
.TP
.BR LIRC_NOTIFY_DECODE " (\fIvoid\fP)"
This ioctl is called by
.BR lircd (8)
whenever a successful decoding of an incoming IR signal is possible.
This can be used by supporting hardware to give visual user
feedback, for example by flashing an LED.
.\"
.SH FEATURES
.PP
The features returned by
The
.BR LIRC_GET_FEATURES
ioctl returns a bit mask describing features of the driver.
The following bits may be returned in the mask:
.TP
.BR LIRC_CAN_REC_RAW
The driver is capable of receiving using
.BR LIRC_MODE_RAW .
.TP
.BR LIRC_CAN_REC_PULSE
The driver is capable of receiving using
.BR LIRC_MODE_PULSE .
.TP
.BR LIRC_CAN_REC_MODE2
The driver is capable of receiving using
.BR LIRC_MODE_MODE2 .
.TP
.BR LIRC_CAN_REC_LIRCCODE
The driver is capable of receiving using
.BR LIRC_MODE_LIRCCODE .
.TP
.BR LIRC_CAN_SET_SEND_CARRIER
The driver supports changing the modulation frequency using
.BR LIRC_SET_SEND_CARRIER .
.TP
.BR LIRC_CAN_SET_SEND_DUTY_CYCLE
The driver supports changing the duty cycle using
.BR LIRC_SET_SEND_DUTY_CYCLE .
.TP
.BR LIRC_CAN_SET_TRANSMITTER_MASK
The driver supports changing the active transmitter(s) using
.BR LIRC_SET_TRANSMITTER_MASK .
.TP
.BR LIRC_CAN_SET_REC_CARRIER
The driver supports setting the receive carrier frequency using
.BR LIRC_SET_REC_CARRIER .
.TP
.BR LIRC_CAN_SET_REC_DUTY_CYCLE_RANGE
The driver supports
.BR LIRC_SET_REC_DUTY_CYCLE_RANGE .
.TP
.BR LIRC_CAN_SET_REC_CARRIER_RANGE
The driver supports
.BR LIRC_SET_REC_CARRIER_RANGE .
.TP
.BR LIRC_CAN_GET_REC_RESOLUTION
The driver supports
.BR LIRC_GET_REC_RESOLUTION .
.TP
.BR LIRC_CAN_SET_REC_TIMEOUT
The driver supports
.BR LIRC_SET_REC_TIMEOUT .
.TP
.BR LIRC_CAN_SET_REC_FILTER
The driver supports
.BR LIRC_SET_REC_FILTER .
.TP
.BR LIRC_CAN_MEASURE_CARRIER
The driver supports measuring of the modulation frequency using
.BR LIRC_SET_MEASURE_CARRIER_MODE .
.TP
.BR LIRC_CAN_USE_WIDEBAND_RECEIVER
The driver supports learning mode using
.BR LIRC_SET_WIDEBAND_RECEIVER .
.TP
.BR LIRC_CAN_NOTIFY_DECODE
The driver supports
.BR LIRC_NOTIFY_DECODE .
.TP
.BR LIRC_CAN_SEND_RAW
The driver supports sending using
.BR LIRC_MODE_RAW .
.TP
.BR LIRC_CAN_SEND_PULSE
The driver supports sending using
.BR LIRC_MODE_PULSE .
.TP
.BR LIRC_CAN_SEND_MODE2
The driver supports sending using
.BR LIRC_MODE_MODE2 .
.TP
.BR LIRC_CAN_SEND_LIRCCODE
The driver supports sending.
(This is uncommon, since
.BR LIRCCODE
drivers reflect hardware like TV-cards which usually dos not support
sending.)
.\"
.SH BUGS
Using these devices requires the kernel source header file
.IR lirc.h .
This file is not available before kernel release 4.6.
Users of older kernels could use the file bundled in
.UR http://www.lirc.org
.UE .
.\"
.SH SEE ALSO
.BR lircd (8)
.PP
https://www.kernel.org/doc/htmldocs/media_api/lirc_dev.html